How to remove echo from audio in premiere pro: This wikiHown teaches you how to remove an echo or reverb from an audio file. Most digital audio workstations have built-in effects that you can use to remove ー or at least reduce, echo or reverb from an audio file.
Adobe Audition
Open Adobe Audition. It has a green square icon that says “Au” in the middle. Click the icon to open Adobe Audition. Adobe Audition has an effect you can use to easily remove or reduce echo and reverb from an audio file. You must purchase a subscription to download and use Adobe Audition.
- The DeReverb effect is not available on older versions of Adobe Audition. However, there are 3rd-party Dereverb effect plug-ins you can purchase that work with nearly all digital audio workstations. Some include a free trial.
Related Articles: How to make a microphone sound better live on pc
Open the audio file you want to remove echo from. Adobe Audition supports most audio formHow to make a microphone sound better live on pcats, including mp3, wav, aiff, flac, ogg, and ffmpeg and more. Use the following steps to open an audio file in Adobe Audition:
- Click File in the menu bar at the top.
- Click Open.
- Select the file you want to edit.
- Click Open.
Select the entire wave file. To select the entire audio file, simply double-click it. You can also click and drag to select a section of the audio file.
Select the DeReverb effect. Use the following steps to select the DeReverb effect.
- Click Effects in the menu at the top.
- Click Noise Reduction/Restoration.
- Click DeReverb.
Click the play icon
to hear the audio. It’s in the lower-left corner of the DeReverb effect window. This allows you to hear what the audio sounds like with DeReverb applied.
- You can also click the power icon (the circle with a line through the top) in the lower-left corner to turn off the effect. This allows you to hear what the audio sounds like before and after DeReverb is applied.
Drag the slider bar next to “Amount”. To increase or decrease the amount of DeReverb you want to add, click and drag the slider bar next to “Amount” at the bottom fo the DeReverb effect window. Applying too much DeReverb will degrade the quality of audio. Applying too little will leave some residual echo or reverb left over. Be sure to click the Play icon in the lower-left corner to hear what the audio sounds like with the current amount of DeReverb.
Click Apply. When you are satisfied with how the audio sounds, click Apply in the lower-right corner of the effect window.
Open the Amplitude Statistics window. Use the following steps to open the Applitude Statistics window:
- Click Window in the menu bar at the top.
- Click Amplitude Statistics.
- Click Scan Selection in the lower-left corner.
Note the Average RMS Amplitude. It’s under the “General” tab in the Amplitude Statistics window.
Add the Dynamics effect. Dynamics has a noise gate you can use to limit the amount of sound in between spoken words. Use the following steps to add Dynamics.
- Dynamics is not available on older versions of Adobe Audition, but there are third-party noise gate effects you can download that work with nearly all digital audio workstations.
Check “AutoGate”. It’s on the left side of the Dynamics effect window.
Set the Threshold as the same number as your Average RMS Amplitude. You can click the number below the Threshold knob below AutoGate and type the number you noted as your Average RMS Amplitude in the Amplitude Statistics window. Round the number up if needed.
Click the play icon to hear the audio. It’s in the lower-left corner of the Dynamics effect window. This allows you to hear what the audio sounds like with Dynamics applied.
Increase the Hold time as needed. If the AutoGate is cutting off parts of your spoken words, click and drag the know that says “Hold” to increase the hold time. Click the play icon to hear how the audio sounds. Repeat until the AutoGate cuts out excess noise in between words, but not any part of the spoken words themselves.
- You may also want to decrease the release time to 50 ms.
Click Apply. When you are satisfied with how the audio sounds, click Apply in the lower-left corner of the effect window to apply Dynamics with the AutoGate.
Export the audio file. If you are satisfied with how the audio sounds, you can export the audio file in AIFF, MP3, Quicktime, or Wav formats. Use the following steps to export your audio file.
Click File.
Click Save As.
Enter a name for the file next to “Filename.” You may want to use a different file name from the original.
Select the desired format using the drop-down menu next to “Format.”
Click Save.
Related Questions: How to remove echo from audio in premiere pro
-
What you mean by Echo?
the repetition of a sound that is caused by reflection of sound waves. 2 : the sound that is due to reflection of sound waves. Other Words from echo.
-
What is Echo and how does it work?
Echoes. An echo is a sound that is repeated because the sound waves are reflected back. Sound waves can bounce off smooth, hard objects in the same way as a rubber ball bounces off the ground. Although the direction of the sound changes, the echo sounds the same as the original sound.
-
How do I setup my Echo?
Set Up Your Echo
Plug in your device.
Open the Alexa app .
Open More and select Add Device.
Select Amazon Echo.
Select Echo, Echo Dot, Echo Plus and more. Follow the instructions to set up your device.